error code 13

fixxxer · Bericht door **fixxxer** » 24 jun 2005 18:26

I conected pin A+B and it gave me code 13. I erased the faultcodes an went for a drive then cheked again and there were no errors. Couple days ago the engine lamp flashed, so i cheked for errors and it gave me 13 again

what should i do?

astra gsi 1994 c20xe

Dima

Bericht door **Laagvlieger** » 24 jun 2005 18:42

The traction control diagnostics don't kow the code 13.
maybe you counted it wrong?

Rijontzegging · Bericht door **Rijontzegging** » 24 jun 2005 19:21

ja maar hij leest nu zn "gewone systeem"toch uit met a en b
want zn tc systeem uitlezen lukte em nie.

faultcode 13: Oxygen sensor open circuit (not 100% sure)

fixxxer · Bericht door **fixxxer** » 24 jun 2005 20:56

"Heated oxygen sensor (HO2S)/ oxygen sensor (O2S)- open circuit"
It is writen at the trouble code 13 at AUTODATA 2004 program.

I've been told that it's located near the exoust, but i can't find it.
somebody please can uploat a foto of that sensor or its location.

Laagvlieger, i am talking about pin A+B. http://www.astragsi.cwc.net/faultcode.htm

Bericht door **Laagvlieger** » 24 jun 2005 22:14

ok sorry, i don't know what the pins do, because i use the TECH 1 as i told you

Bericht door **Bart(astra)** » 25 jun 2005 00:29

The oxigine sensor also lambda sensor is in the exhaust manifold just behind the blok itself. The wire goes up to a connector with 4 pins.

fixxxer · Bericht door **fixxxer** » 02 jul 2005 20:42

is it the sensor that needs to be replace?
http://cgi.ebay.de/ws/eBayISAPI.dll?Vie ... 30731&rd=1

Bericht door **Marty** » 02 jul 2005 21:02

Thats the one!

fixxxer · Bericht door **fixxxer** » 06 jul 2005 19:15

how much this sensor costs in Holland or Germany a new one from Opel dealer?

Does anybody knows its catalog number?

Road-Runner · Bericht door **Road-Runner** » 06 jul 2005 20:00

of deze:

http://www.topbuzz.co.uk/info/fault_cod ... _codes.htm

fixxxer · Bericht door **fixxxer** » 07 jul 2005 22:38

i cleaned the conectors with a special spray, reconected it and took off the negative battery for couple minutes. the 13 error is gone

now i have new error number 38

where is that sensor located?

Bericht door **Laagvlieger** » 07 jul 2005 23:07

error code 38 is the same sensor. The Oxigen sensor. But now it has no voltage output, so the sensor is defective or you have a short circuit in the sensor wiring.

fixxxer · Bericht door **fixxxer** » 16 jul 2005 12:46

hi

I bought a new lamda sensor. It is not origenal GM sensor, but it's new and cost about 65 euro. origenal sensor at opel dealer costs 240 euro.

The new sensor has three wiers. two of them white and one black. It has no connector, only chted wires. The origenal sensor also has 3 wiers, two white and one black.

Do i have to connect the white wier to white and black to black? Does it matters witch white wire to connecto to oter wire (because it has 2 white)?

Dima

Bericht door **Laagvlieger** » 16 jul 2005 16:59

just put color on color.
Black was the output signal of the sensor and white is for the sensor heating.

fixxxer · Bericht door **fixxxer** » 16 jul 2005 19:07

a already installed it. the engine runs better. i went for a chekink spin and accidently killed a little bird.

gsi is ok

Dima

Bericht door **Laagvlieger** » 16 jul 2005 19:18

ok, Stupid bird.